Faber Kitchen Chimney Repair & Cleaning Service in Dehradun

Common Problems We Check (Faber Models):

• Side extraction louvers oily grease se block hone par smoke kitchen mein leak hona
• Centrifugal twin-suction turbine par oil crust jama hone se heavy vibration
• Touch panel par speed 3 select karne par motor restart hona
• Oil collector channel overflow hokar gas stove burner par tapakna

Parts Inspected: 3D diversion cowl, side baffle filters, twin runner turbine, high-torque copper motor, capacitive touch PCB.

Common Problems We Check (Faber Models):

• Auto-clean button press karne par heating strip garam na hona aur buzzer bajna
• Blower wheel unbalance hone se metallic grinding noise create hona
• Motion gesture wave sensor kitchen light change par self-trigger hona
• Oil gutter pipe block hone se oil collection tray bilkul empty rehna

Parts Inspected: PTC auto-clean heating strip, wave gesture sensor board, metal blower impeller, oil drip tray.

Common Problems We Check (Faber Models):

• Baffle plates choked hone se smoke kitchen slab par ghoomna
• Curved tempered glass mounting brackets loose hokar rattle karna
• Push switch bank ke mechanical locks stuck ho jana
• LED warm spotlight ka driver circuit burn ho jana

Parts Inspected: Stainless steel baffle filters, glass rubber grommets, 3-speed push switch unit, LED driver module.

Common Problems We Check (Faber Models):

• Ceiling hanging brackets mein slack aane se chimney body tilt hona
• Long duct pipe run mein oil condensation hone se duct joints se leak hona
• Remote control unit aur ceiling sensor PCB ke beech communication break hona
• High speed par ceiling reverberation aur air turbulence sound aana

Parts Inspected: Ceiling anchor assembly, 150mm aluminum expandable duct, RF remote receiver, BLDC blower motor.

Issue #1: Low Suction Force

Low Suction Force: Chimney chal rahi hai lekin kadhai ka dhuwan bahar nahi nikal raha kyunki baffle filters aur turbine blades thick oil layer se covered hain.

Issue #2: Auto-Clean Heater Failure

Auto-Clean Heater Failure: Heat auto-clean run karne par oil melt nahi ho raha aur heating element cold rehta hai.

Issue #3: Motor Humming But Not Rotating

Motor Humming But Not Rotating: Motor se 'hummmm' sound aati hai lekin fan rotate nahi hota; starting capacitor weak ya dry bearing jam hona.

Issue #4: Touch Screen & Gesture Sensor Malfunction

Touch Screen & Gesture Sensor Malfunction: Haath wave karne par chimney on nahi hoti ya steam moisture ki wajah se touch panel freeze ho jata hai.

Issue #5: Oil Dripping on Gas Stove

Oil Dripping on Gas Stove: Slanted internal channel choked hone se oil direct gas burner par tapakta hai jo flame ko yellow karta hai.

Issue #6: Loud Rattling Noise on High Speed

Loud Rattling Noise on High Speed: Blower fan blade par uneven oil cake jama hone se high RPM par violent vibration create hoti hai.

Issue #7: Chimney Tripping MCB

Chimney Tripping MCB: Internal wiring insulation melt hone ya motor coil short circuit hone se kitchen switchboard ka MCB trip ho jata hai.

Baffle filters ka chemical foam soak, heavy oil removal, water spray rinse aur drying. Ideal for regular 3-month maintenance.

Most Popular

Complete unit dismantling: blower fan impeller chemical wash, motor casing cleaning, internal oil gutter unclogging aur duct check.

Auto-clean heating element resistance check, internal oil drainage channel clearing, oil cup replacement and heating cycle testing.

Field Situation #1

Faber Hood Primus Auto-Clean Failure in Rajpur Road

Resident reported that Faber auto-clean was not melting oil and chimney had low suction. Our technician inspected the unit, checked the PTC heating coil resistance with a multimeter and found a cracked heating connector. Replaced the heat element, cleaned the oil drainage runner, and tested the auto-clean cycle in front of the customer.

Field Situation #2

Faber 3D T2S2 Blower Humming Noise in Jakhan

A flat owner in Jakhan faced loud humming and zero fan movement on their Faber 3D chimney. The technician opened the motor housing, identified a blown 5uF capacitor and dried up motor shaft bushings. Installed a new capacitor, lubricated the rotor with high-temp grease, and restored full 1290 m3/hr suction.

Field Situation #3

Faber Hood Zenith Gesture Sensor Glitch in Vasant Vihar

Customer in Vasant Vihar noticed the Faber gesture sensor kept turning on and off automatically while cooking. Inspection revealed steam moisture had condensed inside the front glass panel, corroding optical wave sensor solder tracks. Technician dried the assembly, cleaned corrosion, resealed the front panel with silicon, and verified smooth gesture operation.

Field Situation #4

Faber Glassy 60 Heavy Oil Dripping in Garhi Cantt

The household in Garhi Cantt was troubled by black grease drops falling into their food while cooking. Technician performed complete disassembly, washed heavily choked baffle filters in chemical degreaser, unclogged the internal slope runner, and realigned the oil cup. Chimney was tested with zero oil leakage.

Field Situation #5

Faber Curved Glass Violent Vibration in Patel Nagar

A resident in Patel Nagar reported extreme vibration that rattled the wall tiles whenever the Faber chimney was switched to speed 3. Our technician dismantled the blower fan and found a 3mm thick hardened oil crust on only one side of the turbine wheel. After thorough chemical ultrasonic cleaning and rebalancing the wheel, the motor ran whisper quiet.

Field Situation #6

Faber Island Chimney Duct Tear in Sahastradhara Road

Apartment owner in Sahastradhara Road observed smoke blowing back through the ceiling gypsum cove. Technician inspected the false ceiling duct run and found a ripped flexible pipe punctured by sharp metal frame edges. Replaced it with a 10-foot heavy-gauge aluminum duct pipe and clamped it securely.

Field Situation #7

Faber Push Button Stuck in Dalanwala

Older Faber baffle chimney in Dalanwala had its speed 2 push button permanently depressed due to grease gumming. Technician dismantled the switch bank, cleaned the sliding brass contacts with contact cleaner spray, replaced the return spring, and restored smooth mechanical switching.

Field Situation #8

Faber Hood Orient Complete Deep Cleaning in Ballupur

After 2 years of continuous frying without service, customer in Ballupur booked complete degreasing. Our two technicians laid cooktop drop sheets, dismantled the entire chimney assembly, soaked baffles and blower in degreasing liquid, reassembled the unit and verified 100% smoke suction.

Field Situation #9

Faber Touch Display Dead After Voltage Fluctuation in Prem Nagar

Following a power spike in Prem Nagar, a Faber chimney went completely blank. Technician diagnosed the main SMPS power supply board, replaced a blown MOV surge protector and internal glass fuse, saving the customer from buying an expensive new motherboard.

Field Situation #10

Faber Chimney Low Suction Diagnosis in Clement Town

Customer complained that even on speed 3, garlic and onion tadka fumes were lingering in the kitchen. Technician checked the exterior wall cowl and found pigeon feathers and oil lint had completely jammed the outer flap. Cleared the wall louvers, installed a wire mesh guard, and restored original airflow.

Cooktop & Kitchen Tile Protection

Degreasing aur disassembly ke dauran gas stove aur marble counter par protective sheet lagayi jaati hai taaki kitchen ganda na ho aur mess-free service mile.

Repair & Deep Cleaning Together

Sirf filter wash nahi, balki motor rewiring, capacitor change, PCB soldering, touch panel replacement aur duct pipe fitting ka complete technical solution.

Faber Hardware Experience

Technicians Faber ke auto-clean heating circuits, touch gestures, blower turbines aur duct couplings ke exact technical specs se well-trained hain.

Transparent Price Approval

Technician inspection karke exact problem identify karta hai aur spare part ya labour ka estimate pehle customer ke sath share karke approve karwata hai.

All 7 Days Availability

Morning 8:00 AM se Evening 8:30 PM tak service booking open rehti hai. Working professionals ke liye weekend aur holiday visits bhi smoothly schedule hote hain.

Local Dehradun Fast Response

Dehradun ke alag-alag zones mein stationed technicians ki wajah se booking ke 2 se 4 ghante ke andar doorstep attendance possible ho pati hai.

Share Faber Model Issue

Call ya WhatsApp par chimney ka issue (low suction, noise, oil leak ya panel dead) aur model share karein.

Doorstep Slot Scheduling

Aapki convenience ke hisab se same-day visit schedule ki jaati hai aur technician details share hoti hain.

Cooktop Prep & Inspection

Technician cooktop par drop cloth bichhata hai aur airflow, motor winding, capacitor aur heating element diagnose karta hai.

Estimate & Customer Approval

Problem aur required spare part ka clear estimate bataya jata hai. Customer ke approve karne ke baad hi work start hota hai.

Repair / Degreasing Execution

Disassembly, chemical degreasing wash, motor capacitor replacement, switch fitting ya duct pipe repair kitchen mein clean tarike se execute hota hai.

Airflow Testing & Payment

Reassembly ke baad suction paper test, noise level test aur auto-clean heating check customer ko dikhaya jata hai. Verification ke baad hi payment hoti hai.